| 91.40.2199.991.41.1502 Standard 5 Slewing Ring Bearings | L:279.4 mm; Max. speed for Taconite seal:1400 r/min; J min.:206.375 mm; Stabilizing ring:SR-13-0; J max.:241.3 mm; P180°:19.1 kN; P150°:16 kN; R1:44.45 mm; Pa:6.09 kN; H1:76.2 mm; Cap bolt recommended tightening torque:81.3 N·m; H2:25.4 mm; P90°:30.2 kN; h:27.781 mm; PG:1/8 NPT; A1:79.375 mm; Taconite seal:TER 30; H:147.637 mm; ba:31.75 mm; N1:19.05 mm; |
| 1 0422 01 Rollix Slewing Ring Bearings | R1:87.313 mm; RG:3/4 NPT; J min.:406.4 mm; Cap bolt:7/8-9 UNC; H1:152.4 mm; N1:28.575 mm; Cap bolt, SAE grade:8; J max.:434.975 mm; h:44.45 mm; P180°:127 kN; Mass pillow block:87.5 kg; Stabilizing ring:2 x SR-0-24; Initial grease fill:481.95 g; H:298.45 mm; R2:38.1 mm; Ca:86.614 mm; P90°:180 kN; P60°:301 kN; ba:64.294 mm; P150°:105 kN; |
| 8 0475 08 Rollix Slewing Ring Bearings | d:20.000 mm; Accessories:One Seal & Snap-Ring; Basic Dynamic Radial Load Rating C:23800 N; Basic Static Radial Load Rating Co:20000 N; D:52.0000 mm; Oil Speed Rating n2:12000 rpm; Grease Speed Rating n1:8500 rpm; Fillet Radius ra:1.00 mm; B:22.20 mm; Sealed Speed Rating n3:8500 rpm; |
| 12.40.2950.001.41.1502 Standard 5 Slewing Ring Bearings | Fillet Radius ra:1.00 mm; d:20.000 mm; D:47.0000 mm; Fillet Radius rb:0.60 mm; Basic Static Radial Load Rating Co:7800 N; B:14.00 mm; Oil Speed Rating n2:50000 rpm; Grease Speed Rating n1:35000 rpm; Basic Dynamic Radial Load Rating C:13000 N; |
| 191.25.2000.990.41.1502 Standard 5 Slewing Ring Bearings | P120°:30.2 kN; N1:22.225 mm; P60°:83.2 kN; P90°:49.8 kN; H1:88.9 mm; ba:40.481 mm; Labyrinth ring:2 x LOR 32; Ca:57.785 mm; Initial grease fill:87.885 g; R2:21.431 mm; H:167.481 mm; A1:88.9 mm; h:35.719 mm; S:4.763 mm; J min.:244.475 mm; RG:3/8 NPT; A2:134.938 mm; Stabilizing ring:SR-16-13; Cap bolt:2 x 5/8-11 UNC; H2:31.75 mm; |
| 162.36.2000.891.41.1503 Standard 5 Slewing Ring Bearings | Specific dynamic load factor K:40 N/mm²; Coefficient of friction µ min.:0.08; Mass bushing:0.011 kg; B:25 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7 m/s; Coefficient of friction µ max.:0.15; Specific static load factor K0:120 N/mm²; d:16 mm; D:18 mm; Tolerance shaft:f7 m/s; Permissible sliding velocity v max.:1 m/s; |
| 11.40.3150.001.41.1502 Standard 5 Slewing Ring Bearings | Basic Dynamic Radial Load Rating C:143000 N; d:110.000 mm; B:38.00 mm; Grease Speed Rating Open/Shielded n1:3000 rpm; D:200.0000 mm; Oil Speed Rating Open/Shielded n2:3600 rpm; Basic Static Radial Load Rating Co:118000 N; Grease Speed Rating n1:3000 rpm; Sealed Speed Rating n3:2000 rpm; Accessories:Without Accessories; Fillet Radius ra:2.00 mm; Oil Speed Rating n2:3600 rpm; |
| 92.35.1802.990.11.1502 Standard 5 Slewing Ring Bearings | l5 ≈:45 mm; d:80 mm; l3 min.:85 mm; l4 max.:389 mm; h1:295 mm; G:M 80; w:90 mm; l7 min.:88 mm; d2 max.:182 mm; Specific dynamic load factor K:100 N/mm²; Basic static load rating C0:655 kN; Basic dynamic load rating C:400 kN; α:6 °; r1 min.:1 mm; B:55 mm; Material constant KM:330; Mass rod end:15 kg; d4 ≈:105 mm; dk:105 mm; C1 max.:48 mm; |
| 162.50.2660.891.41.1503 Standard 5 Slewing Ring Bearings | d:6 mm; r1,2 min.:0.3 mm; Mass bearing:0.013 kg; da max.:10.4 mm; Calculation factor kr:0.035; da min.:8 mm; Da max.:20 mm; Reference speed:75000 r/min; Basic dynamic load rating C:1.99 kN; Fatigue load limit Pu:0.034 kN; D2 ≈:19.03 mm; Calculation factor f0:7.2; d2 ≈:10.5 mm; ra max.:0.3 mm; Basic static load rating C0:0.78 kN; Limiting speed:38000 r/min; B:7 mm; D:22 mm; |
| 191.50.5000.990.41.1502 Standard 5 Slewing Ring Bearings | A2:206.375 mm; J min.:263.525 mm; Cap bolt:1/2-13 UNC; Da:160 mm; Housing:FSAFS 518; J max.:295.275 mm; P120°:59.6 kN; A1:98.425 mm; S:4.763 mm; P180°:64.9 kN; P90°:94.3 kN; P150°:54.3 kN; ba:40.481 mm; J1:53.975 mm; Pa:10.9 kN; Cap bolt, SAE grade:8; N1:19.05 mm; R2:27.781 mm; da:79.375 mm; Max. speed for Taconite seal:950 r/min; |
| 92.40.2003.991.41.1502 Standard 5 Slewing Ring Bearings | B:240 mm; Reference speed:600 r/min; Da min.:651 mm; Limiting speed:800 r/min; d:460 mm; Operating clearance factor k2:0.105; d2 ≈:559 mm; s1 max.:51 mm; Misalignment factor k1:0.108; Mass bearing:435 kg; Fatigue load limit Pu:815 kN; r1,2 min.:7.5 mm; Ca min.:4.2 mm; D1 ≈:679 mm; ra max.:6 mm; da max.:603 mm; D:760 mm; Basic static load rating C0:12000 kN; Da max.:728 mm; da min.:492 mm; |
| 11.40.2619.001.41.1502 Standard 5 Slewing Ring Bearings | Basic static load rating C0:13.7 kN; Mass needle roller and cage assembly:0.0075 kg; U:10 mm; Fatigue load limit Pu:1.56 kN; Fw:22 mm; Ew:26 mm; Limiting speed:20000 r/min; Reference speed:18000 r/min; Basic dynamic load rating C:8.8 kN; |
| 35 0411 01 Rollix Slewing Ring Bearings | d:150.000 mm; Grease Speed Rating n1:1700 rpm; Fillet Radius ra:2.00 mm; Basic Static Radial Load Rating Co:180000 N; D:235.0000 mm; B:38.00 mm; Basic Dynamic Radial Load Rating C:159000 N; Fillet Radius rb:1.00 mm; Oil Speed Rating n2:2800 rpm; |
| 37 0411 01 Rollix Slewing Ring Bearings | Coefficient of friction µ max.:0.1; Permissible sliding velocity v min.:0.25 m/s; d:12 mm; Specific static load factor K0:20 N/mm²; B:25 mm; Tolerance shaft:h8; D:25 mm; Permissible sliding velocity v max.:5 m/s; Tolerance housing:H7; Specific dynamic load factor K:10 N/mm²; Mass bushing:0.058 kg; Coefficient of friction µ min.:0.05; |